Makita JV100D Manual de Instruções Página 9
- Página / 32
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
9
Bevel cutting (Fig. 9)
CAUTION:
•Always be sure that the tool is switched off and the
battery cartridge is removed before tilting the base.
•Raise the dust cover all the way before making bevel
cuts.
With the base tilted, you can make bevel cuts at any angle
between 0° and 45° (left or right).
Loosen the bolt on the back of the base with the hex
wrench. Move the base so that the bolt is positioned in the
center of the cross-shaped slot in the base. (Fig. 10)
Tilt the base until the desired bevel angle is obtained. The
edge of the motor housing indicates the bevel angle by
graduations. Then tighten the bolt to secure the base.
(Fig. 11)
Front flush cuts (Fig. 12)
Loosen the bolt on the back of the base with the hex
wrench and slide the base all the way back. Then tighten
the bolt to secure the base.
Cutouts
Cutouts can be made with either of two methods A or B.
A) Boring a starting hole (Fig. 13)
For internal cutouts without a lead-in cut from an edge,
pre-drill a starting hole 12 mm or more in diameter.
Insert the blade into this hole to start your cut.
B) Plunge cutting (Fig. 14)
You ne e d n o t bore a sta rting hole or ma k e a lead-in
cut if you carefully do as follows.
(1) Tilt the tool up on the front edge of the base with
the blade point positioned just above the
workpiece surface.
(2) Apply pressure to the tool so that the front edge
of the base will not move when you switch on the
tool and gently lower the back end of the tool
slowly.
(3) As the blade pierces the workpiece, slowly lower
the base of the tool down onto the workpiece
surface.
(4) Complete the cut in the normal manner.
Finishing edges (Fig. 15)
To trim edges or make dimensional adjustments, run the
blade lightly along the cut edges.
Metal cutting
Always use a suitable coolant (cutting oil) when cutting
metal. Failure to do so will cause significant blade wear.
The underside of the workpiece can be greased instead of
using a coolant.
Dust extraction (Fig. 16)
Clean cutting operations can be performed by connecting
this tool to a Makita vacuum cleaner. Insert the hose of the
vacuum cleaner into the hole at the rear of the tool. Lower
the dust cover before operation.
NOTE:
• Dust extraction cannot be performed when making
bevel cuts.
Rip fence (optional accessory)
CAUTION:
•Always be sure that the tool is switched off and the
battery cartridge is removed before installing or
removing accessories.
1. Straight cuts (Fig. 17)
When repeatedly cutting widths of 160 mm or less,
use of the rip fence will assure fast, clean, straight
cuts.
To in stal l , i n se r t th e ri p f e nce int o th e re c ta ngu l ar ho le
on the side of the base with the fence guide facing
down. Slide the rip fence to the desired cutting width
position, then tighten the bolt to secure it. (Fig. 18)
2. Circular cuts
When cutting circles or arcs of 170 mm or less in
radius, install the rip fence as follows.
Insert the rip fence into the rectangular hole on the
side of the base with the fence guide facing up. Insert
the circular guide pin through either of the two holes
on the fence guide. Screw the threaded knob onto the
pin to secure the pin. (Fig. 19)
Now slide the rip fence to the desired cutting radius,
and tighten the bolt to secure it in place. Then move
the base all the way forward. (Fig. 20)
NOTE:
•Always use blades No. B-17, B-18, B-26 or B-27 when
cutting circles or arcs.
Anti-splintering device
(optional accessory) (Fig. 21)
For splinter-free cuts, the anti-splintering device can be
used. To install the anti-splintering device, move the tool
base all the way forward and fit it from the back of tool
base. When you use the cover plate, install the anti-
splintering device onto the cover plate.
CAUTION:
•The anti-splintering device cannot be used when
making bevel cuts.
Cover plate (optional accessory) (Fig. 22)
Use the cover plate when cutting decorative veneers,
plastics, etc. It protects sensitive or delicate surfaces from
damage. Fit it on the back of the tool base.
MAINTENANCE
CAUTION:
•Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To ma inta i n p r odu c t S A FET Y an d R ELI AB I LIT Y, r e pai r s,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
•These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
- 1 012335 2 012312 2
- 4 012314 2
- 3 012313 5 012315 2
- 6 012316 7 012318 2
- 8 012319 9 012320 3
- 10 012321 11 012322 3
- 12 012323 13 012324 3
- 14 012325 15 012326 3
- 16 012327 17 012328 4
- 18 012329 19 012330 4
- 20 012331 21 012333 4
- 22 012334 4
- SPECIFICATIONS 5
- General Power Tool Safety 5
- Warnings GEA006-2 5
- Save all warnings and 5
- (Fig. 1) 7
- ASSEMBLY 8
- OPERATION 8
- MAINTENANCE 9
- OPTIONAL ACCESSORIES 9
- END004-4 11
- ENE019-1 11
- GEA006-2 11
- GEB045-2 13
- ENC009-1 13
- DESKRIPSI FUNGSI 14
- PERAKITAN 14
- PENGOPERASIAN 15
- AKSESORI TAMBAHAN 16
- PERAWATAN 16
- QUAÙ TRÌNH LAÉP RAÙP 20
- VAÄN HAØNH 20
- BAÛO DÖÔÕNG 21
- PHUÏ KIEÄN TUYØ CHOÏN 22
- 23
- 23
- 25
- GEB045-2 25
- 25
- 26
- 26
- 27
- 27
- ° 45° () 28
- 29
- 29
- Makita Corporation 32
Manuais e produtos relacionados com Motosserras sem fio Makita JV100D
(1 páginas)Pro-link Air Freshener Crisp Apple B14269 EN manuály
Uživatelské manuály a uživatelské příručky pro Pro domov Pro-link Air Freshener Crisp Apple B14269 EN.
Poskytujeme 1 manuály pdf Pro-link Air Freshener Crisp Apple B14269 EN ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais