Makita LS711D Especificações

INSTRUCTION MANUALWARNING:For your personal safety, READ and UNDERSTAND before using.SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.Cordless Slide Compo

10Trickle charge (Maintenance charge)If you leave the battery cartridge in the charger to preventspontaneous discharging after full charge, the charge

11If the blade guard is especially dirty and vision through theguard is impaired, use the supplied socket wrench to loosenthe hex bolt holding the cen

12Maintaining maximum cutting capacityThis tool is factory adjusted to provide the maximum cuttingcapacity for a 190 mm (7-1/2”) saw blade.When instal

13Adjusting the miter angleLoosen the grip by turning counterclockwise. Turn the turnbase while pressing down the lock lever. When you havemoved the g

14• Do not pull the switch trigger hard without pressing in thelock-off button. This can cause switch breakage.To prevent the switch trigger from bein

15Socket wrench storageThe socket wrench is stored as shown in the figure. Whenusing the socket wrench, pull it out of the wrench holder.After using t

16Press the shaft lock to lock the spindle and use the socketwrench to loosen the hex bolt clockwise. Then remove thehex bolt, outer flange and blade.

17Dust bagThe use of the dust bag makes cutting operations clean anddust collection easy. To attach the dust bag, fit it onto thedust nozzle.When the

18Vertical viseThe vertical vise can be installed in two positions on eitherthe left or right side of the guide fence or the holder assembly(optional

19Holders and holder assembly (optional accessories)The holders and the holder assembly can be installed oneither side as a convenient means of suppor

2SPECIFICATIONSBlade diameter ... 190 mm (7-1/2”)Hole (arbor)

201. Press cutting (cutting small workpieces)Workpieces up to 50 mm (2”) high and 97 mm (3-13/16”)wide can be cut in the following way.Push the carria

21• Never perform the slide cut with the handle locked in thelowered position by pressing the stopper pin.• Never loosen the clamp screw which secures

22When performing compound cutting, refer to “Press cut-ting”, “Slide cutting”, “Miter cutting” and “Bevel cut”explanations.6. Cutting crown and cov

23Example:In the case of cutting 52/38° type crown molding forposition (1) in Fig. A:• Tilt and secure bevel angle setting to 33.9°LEFT.• Adjust and s

24EN0002-1Compound Miter Saw Miter and Bevel Angle Settings00003152˚38˚CeilingWallWall to Crown Molding Angle: 52/38 degreesWall Angle (deg.)Bevel Ang

25 EN0003-1Compound Miter Saw Miter and Bevel Angle Settings00003245˚45˚CeilingWallWall to Crown Molding Angle: 45 degreesWall Angle (deg.)Bevel Angle

267. Cutting repetitive lengthsWhen cutting several pieces of stock to the same length,ranging from 220 mm (8-5/8”) to 385 mm (15-1/8”), useof the set

27Carry the tool by carrying grip as shown in the figure. If youremove the holders, dust bag, etc., you can carry the toolmore easily.CAUTION:• Always

28Make sure that the pointer points to 0° on the miterscale. If the pointer does not point to 0°, loosen thescrew which secures the pointer and adjust

29(2) 45° bevel angleAdjust the 45° bevel angle only after performing 0°bevel angle adjustment. To adjust left 45° bevelangle, loosen the lever and ti

3For Your Own Safety Read Instruction Manual Before Operating Tool Save it for future reference GENERAL SAFETY PRECAUTIONSUSA005-1(For All TOOIS)1. KN

30EN0001-1Recycling the BatteryThe only way to dispose of a Makita battery is to recycle it.The law prohibits any other method of disposal.To recycle

31ACCESSORIES• These accessories or attachments are recommended foruse with your Makita tool specified in this manual. Theuse of any other accessories

Memo32

33FoldCutStampTimbreMakita Canada Inc.1950 Forbes Street,Whitby, OntarioL1N 7B7

34Your answers to the following questions are appreciated.Date Purchased Model No.Serial No.Initial Last NameStreet AddressCity ProvinceAGE:Male Femal

35Factory Service CentresFor the authorized service centre nearest you please refer to the local yellow pages directory under “tools” or con-tact our

Warranty PolicyEvery Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects fromworkmanship

418. NEVER STAND ON TOOL. Serious injurycould occur if the tool is tipped or if thecutting tool is unintentionally contacted.19. CHECK DAMAGED PARTS.

5ing it from tool, then cleaning it with gumand pitch remover, hot water or kerosene.Never use gasoline to clean blade.14. While making a slide cut, K

6SAVE THESE INSTRUCTIONSWARNING:MISUSE or failure to follow the safety rules stated in thisinstruction manual may cause serious personal injury.IMPORT

712. To reduce risk of electric shock, unplugcharger from outlet before attempting anymaintenance or cleaning. Turning off con-trols will not reduce t

8INSTALLATIONBench mountingWhen the tool is shipped, the handle is locked in the loweredposition by the stopper pin. Release the stopper pin by lower-

9Charging1. Plug the battery charger into the proper AC voltagesource. The charging light will flash in green color.2. Insert the battery cartridge so