Makita BHR261T Manual do Utilizador

Capacity: mm (")HR262D/ BHR262 HR262TD/ BHR262TYesYesYes (by trigger)13 (1/2)32 (1-1/4)26 (1)4.5 (9.9)Models No. DescriptionCONCEPT AND MAIN APPL

[3] DISASSEMBLY/ASSEMBLY[3]-4. Motor section, SwitchRemove two Pins 6 and two 4x18 Tapping screws,then separate Handle (R) from Handle (L).Switch can

[3] DISASSEMBLY/ASSEMBLY[3]-4. Motor section, Switch (cont.)Remove Brush holder on the right sideby unscrewing two 4x18 Tapping screws.Motor section a

When inserting Armature into Inner housing complete,do not fail to pass Armature through Yoke unit in advance.Note: Yoke unit is not directional when

[3] DISASSEMBLY/ASSEMBLY[3]-5. Tool holder section for BHR262, HR262D/ Tool holder guide section for BHR262T, HR262DTDISASSEMBLINGInner hou

[3] DISASSEMBLY/ASSEMBLY[3]-6. Needle bearing complete and Oil seal 25DISASSEMBLINGFig. 34Fig. 37ASSEMBLING1) Assemble Oil seal 25 to Gear housing com

[3] DISASSEMBLY/ASSEMBLY[3]-7. Impact bolt in Tool holder complete for BHR262, HR262D)/ Tool holder guide complete for BHR262T, HR262T

Note: 2)ASSEMBLINGFig. 42Cushion ring 13 Ring 10O ring case withO ring 9 fit inside Impact bolt1) Assemble Impact bolt section to Tool holder (guide)

[3] DISASSEMBLY/ASSEMBLY[3]-8. Swash bearing 10, Gear sectionDISASSEMBLINGFig. 44Note: This step can be done without removing Motor section. 1) Remove

[3] DISASSEMBLY/ASSEMBLY[3]-8. Swash bearing 10, Gear section (cont.)ASSEMBLINGFig. 51Fig. 52Guide plateNote: Be sure to apply Makita grease RB No.00

[4] Maintenance programIt is recommended to replace the following parts at the same time when replacing Carbon brushes. (Fig. 55)Note: Be sure to put

P 2/22Variation list BHR262Z2CBHR262RDModel No.Type QuantityBatteryadapterBatteryconverterPlasticcarryingcaseBatterycoverYesBatteryBHR262DP1No NoBHR2

Color index of lead wires' sheathBlackTerminalLEDBrush holderSwitchM1WhiteRedFig. D-1TerminalLEDLine filtersSwitchCircuit diagramP 20/22With Equi

Wiring diagramFig. D-2To Brush holdercompleteConnectorConnectorribsDiodeSwitchLead wire holdersFET (Field effect transistor)Lead wires must be tight i

Lead wire (yellow)Terminal Line filtersTubeConnectorLead wire (black)YokeConnectorFETFig. D-3Lead wire holderLead wire holderFix Lead wires (red, blac

[2] LUBRICATION[1] NECESSARY REPAIRING TOOLSRepairDescriptionCode No. Use forRetaining ring S pliers ST-2N1R003Removing Ring spring 19 from Tool holde

Gear section: 17gCrank section: 5gboss for fixingCompressionspring 14[Inside view of Inner housing][2] LUBRICATION (cont.)Apply Makita grease RB No.00

[3] DISASSEMBLY/ASSEMBLY[3] -1. Bit holder section for BHR262, HR262D Holder section for Drill chuck of BHR262T, HR262TDDISASSEMBLING for BH

aNote:Face the chamfered endof the hole upward.Aligning the hole ofChange ring with thatof Change cover,assemble Change ringto Change cover.a'[Se

[3] DISASSEMBLY/ ASSEMBLY[3] -2. Drill chuck assembly for BHR262T, HR262TDDISASSEMBLINGFig. 10 Fig. 11Fig. 14Fig. 13Fig. 12Steel ball 5.0Leaf springFl

Change coverChange ringASSEMBLINGChuck holdershort arm ofTorsion spring 31long arm ofTorsion spring 31hole forTorsion spring 31(1) Holding Chuck holde

[3] DISASSEMBLY/ASSEMBLY[3]-3. Change leverWhile pushing Lock button into Change lever,turn Change lever a little over Drill mode positionto lock it i