Makita BLS820 Especificações

INSTRUCTION MANUALWARNING:For your personal safety, READ and UNDERSTAND before using.SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.Cordless Compound Mi

105. If you leave the battery cartridge in the charger after thecharging cycle is complete, the charger will switch intoits “ trickle charge (mainten

11• Check the sound of cooling fan, vent on the charger andbattery, which can be sometime clogged with dust.• The cooling system is in order although

12Blade guardWhen lowering the handle, the blade guard rises automati-cally. The guard is spring loaded so it returns to its originalposition when the

13Positioning kerf boardThis tool is provided with the kerf boards in the turn base tominimize tearing on the exit side of a cut. The kerf boards aref

14Adjusting the miter angleLoosen the grip by turning counterclockwise. Turn the turnbase while pressing down the lock lever. When you havemoved the g

15• Do not pull the switch trigger hard without pressing in thelock-off button. This can cause switch breakage.To prevent the switch trigger from bein

16Socket wrench storageThe socket wrench is stored as shown in the figure. Whenusing the socket wrench, pull it out of the wrench holder.After using t

17Press the shaft lock to lock the spindle and use the socketwrench to loosen the hex bolt clockwise. Then remove thehex bolt, outer flange and blade.

18Dust bagThe use of the dust bag makes cutting operations clean anddust collection easy. To attach the dust bag, fit it onto thedust nozzle.When the

19Vertical viseThe vertical vise can be installed in two positions on eitherthe left or right side of the guide fence or the holder assembly(optional

2SPECIFICATIONSBlade diameter ... 216 mm (8-1/2”)Hole (arbor)

20CAUTION:• Grip the workpiece only when the projection is at thetopmost position. Failure to do so may result ininsufficient securing of the workpiec

21• Gently press down the handle to perform the cut. If thehandle is pressed down with force or if lateral force isapplied, the blade will vibrate and

22• When pressing the handle down, apply pressure parallelto the blade. If the pressure is not parallel to the bladeduring a cut, the angle of the bla

23There are crown and cove molding joints which aremade to fit “Inside” 90° corners ((1) and (2) in Fig. A) and“Outside” 90° corners ((3) and (4) in F

24Example:In the case of cutting 52/38° type crown molding forposition (1) in Fig. A:• Tilt and secure bevel angle setting to 33.9°LEFT.• Adjust and s

25EN0002-1Compound Miter Saw Miter and Bevel Angle Settings00003152˚38˚CeilingWallWall to Crown Molding Angle: 52/38 degreesWall Angle (deg.)Bevel Ang

26 EN0003-1Compound Miter Saw Miter and Bevel Angle Settings00003245˚45˚CeilingWallWall to Crown Molding Angle: 45 degreesWall Angle (deg.)Bevel Angle

276. Cutting repetitive lengthsWhen cutting several pieces of stock to the same length,ranging from 220 mm (8-5/8”) to 365 mm (14-3/8”), useof the set

28WARNING:• Always be sure that the blade is sharp and clean for thebest and safest performance.Adjusting the cutting angleThis tool is carefully adju

292. Bevel angle(1) 0° bevel angleLower the handle fully and lock it in the loweredposition by pushing in the stopper pin. Loosen thelever at the rear

3For Your Own Safety Read Instruction Manual Before Operating Tool Save it for future reference GENERAL SAFETY PRECAUTIONSUSA005-1(For All TOOIS)1.KNO

30Replacing carbon brushesRemove and check the carbon brushes regularly. Replacewhen they wear down to the limit mark. Keep the carbonbrushes clean an

31ACCESSORIESCAUTION:• These accessories or attachments are recommended foruse with your Makita tool specified in this manual. Theuse of any other acc

Memo32

33FoldCutStampTimbreMakita Canada Inc.1950 Forbes Street,Whitby, OntarioL1N 7B7

34Your answers to the following questions are appreciated.Date Purchased Model No.Serial No.Initial Last NameStreet AddressCity ProvinceAGE:Male Femal

35Factory Service CentresFor the authorized service centre nearest you please refer to the local yellow pages directory under “tools” or con-tact our

Warranty PolicyEvery Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects fromworkmanship

418.NEVER STAND ON TOOL. Serious injurycould occur if the tool is tipped or if thecutting tool is unintentionally contacted.19.CHECK DAMAGED PARTS. Be

514.Make sure that the turn base is properlysecured so it will not move during opera-tion. Use the holes in the base to fastenthe saw to a stable work

6IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGEUSC002-31.SAVE THESE INSTRUCTIONS- This man-ual contains important safety and operat

7ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE1.Do not charge Battery Cartridge whentemperature is BELOW 10°C (50°F) orABOVE 40°C (104°F

8INSTALLATIONInstalling auxiliary plateInstalling the auxiliary plate using the notch in the tool’s baseand secure it by tightening the hex bolt.Bench

9FUNCTIONAL DESCRIPTIONCAUTION:• Always be sure that the tool is switched off and thebattery cartridge is removed before adjusting orchecking function